*** Restricting New Posts to SD Premium Members ONLY *** (09 May 2025)
Just made a new account? Can't post? Click above.
Help us help you. By posting the year, make, model and engine near the beginning of your help request, followed by the symptoms (no start, high idle, misfire etc.) Along with any prevalent Diagnostic Trouble Codes, aka DTCs, other forum members will be able to help you get to a solution more quickly and easily!
ECU programing error message
- Failed Test
-
Topic Author
- Offline
- New Member
-
- Chad
-
- Offline
- Moderator
-
- I am not a parts changer.
4 months 1 week ago #90911
by Chad
"Knowledge is a weapon. Arm yourself, well, before going to do battle."
"Understanding a question is half an answer."
I have learned more by being wrong, than I have by being right.
Replied by Chad on topic ECU programing error message
I don't know what that specific code means but, make sure you have a good, stable power supply and check to ensure that you have the autel VCI drivers installed on your laptop.
"Knowledge is a weapon. Arm yourself, well, before going to do battle."
"Understanding a question is half an answer."
I have learned more by being wrong, than I have by being right.
Please Log in or Create an account to join the conversation.
- Noah
-
- Offline
- Moderator
-
- Give code definitions with numbers!
- Tyler
-
- Offline
- Moderator
-
- Full time HACK since 2012
- Failed Test
-
Topic Author
- Offline
- New Member
-
- Chad
-
- Offline
- Moderator
-
- I am not a parts changer.
4 months 1 week ago - 4 months 1 week ago #91668
by Chad
"Knowledge is a weapon. Arm yourself, well, before going to do battle."
"Understanding a question is half an answer."
I have learned more by being wrong, than I have by being right.
Replied by Chad on topic ECU programing error message
18v on pin 13 enables the module to be programmed.
A few years ago there was a problem with fjds version 113, I believe. I ended up in a situation similar to yours, even though I had 18v on pin 13. I don't recall the error code but, the solution for me was to manually install "as built data".
A few years ago there was a problem with fjds version 113, I believe. I ended up in a situation similar to yours, even though I had 18v on pin 13. I don't recall the error code but, the solution for me was to manually install "as built data".
"Knowledge is a weapon. Arm yourself, well, before going to do battle."
"Understanding a question is half an answer."
I have learned more by being wrong, than I have by being right.
Last edit: 4 months 1 week ago by Chad.
Please Log in or Create an account to join the conversation.
- Failed Test
-
Topic Author
- Offline
- New Member
-
- Chad
-
- Offline
- Moderator
-
- I am not a parts changer.
4 months 1 week ago - 4 months 1 week ago #91780
by Chad
"Knowledge is a weapon. Arm yourself, well, before going to do battle."
"Understanding a question is half an answer."
I have learned more by being wrong, than I have by being right.
Replied by Chad on topic ECU programing error message
The 18v is supplied by the programming tool.
If your tool is not supplying the 18v, I suppose that you could supply an external source but, if the j2534 box is not working, properly, I don't think that I would trust it do the programming.
If you give it a try, be sure to let us know how it went.
Good luck!
If your tool is not supplying the 18v, I suppose that you could supply an external source but, if the j2534 box is not working, properly, I don't think that I would trust it do the programming.
If you give it a try, be sure to let us know how it went.
Good luck!
"Knowledge is a weapon. Arm yourself, well, before going to do battle."
"Understanding a question is half an answer."
I have learned more by being wrong, than I have by being right.
Last edit: 4 months 1 week ago by Chad.
Please Log in or Create an account to join the conversation.
Time to create page: 0.340 seconds