===PCM DTC P0000-61===
Code: P0000 - Unrecognized fault code

Additional Fault Symptom:
 - Signal is Above Maximum Threshold

Status: 
 - DTC Present at Time of Request
 - Malfunction Indicator Lamp is Off for this DTC

Module: Powertrain Control Module

Diagnostic Trouble Code details

Undefined

Error Code

If any other DTC's exist

investigate them first.

===END PCM DTC P0000-61===

===PCM DTC U2005-E1===
Code: U2005 - Audio Integrated Control Panel Unit is not responding

Additional Fault Symptom:
 - Signal is Above Maximum Threshold

Status: 
 - DTC Present at Time of Request
 - Malfunction Indicator Lamp is On for this DTC

Module: Powertrain Control Module

Diagnostic Trouble Code details

Audio Integrated Control Panel Unit is not responding

Operator Action

Run self test.

All CMDTCs

Fix all relevant DTCs then clear codes and retest.

Note:

DTCs that start with 'U' are faults which occur during module-to-module communication.

Modules should never be replaced based only on a 'U' code. These codes do not always indicate a problem, and can be caused by normal diagnostic functions, carried out on the vehicle.

===END PCM DTC U2005-E1===

===OBDII DTC U2005-P===
Code: U2005 - Audio Integrated Control Panel Unit is not responding

Status: 
 - Pending - malfunction is expected to be confirmed 

Module: On Board Diagnostic II

Diagnostic Trouble Code details

Audio Integrated Control Panel Unit is not responding

Operator Action

Run self test.

All CMDTCs

Fix all relevant DTCs then clear codes and retest.

Note:

DTCs that start with 'U' are faults which occur during module-to-module communication.

Modules should never be replaced based only on a 'U' code. These codes do not always indicate a problem, and can be caused by normal diagnostic functions, carried out on the vehicle.

===END OBDII DTC U2005-P===

===AWD DTC None===
Successful DTC reading, no error codes found

Module: All Wheel Drive Module

===END AWD DTC None===

===ABS DTC U0401-A0===
Code: U0401 - Invalid or Missing CAN Data From The PCM

Status: 
 - Previously Set DTC - Not Present at Time of Request
 - Malfunction Indicator Lamp is On for this DTC

Module: Antilock braking system

===END ABS DTC U0401-A0===

===ABS DTC B1317-E0===
Code: B1317 - Battery Voltage Too High

Status: 
 - DTC Present at Time of Request
 - Malfunction Indicator Lamp is On for this DTC

Module: Antilock braking system

Diagnostic Trouble Code details

Battery Voltage Too High

This DTC may be caused by :

Check the condition of the battery.

Check the battery charging system.

Interference caused by non-standard accessories installed.

Electrical Interference

Note: This DTC may set after a 24 volt jump start.

Additional Information

The ABS lamp should be illuminated.

The ESP lamp should be illuminated.

There will be an ESP malfunction warning displayed on the driver information text panel.

===END ABS DTC B1317-E0===

===EPS DTC C1956-20===
Code: C1956 - Steering Angle Sensor Circuit Failure

Status: 
 - Previously Set DTC - Not Present at Time of Request
 - Malfunction Indicator Lamp is Off for this DTC

Module: Electronic-Controlled Power Steering

Diagnostic Trouble Code details

Steering Angle Sensor Circuit Failure

Possible causes are:

Steering Angle Sensor Circuit Failure

Check the wiring and the appropriate fuse.

Carry Out ECU Reset

If the fault is permanant, then the SAS sensor has failed.

Only replace the sensor if the fault still exists.

===END EPS DTC C1956-20===

===EPS DTC U261B-20===
Code: U261B - Improper Program Termination

Status: 
 - Previously Set DTC - Not Present at Time of Request
 - Malfunction Indicator Lamp is Off for this DTC

Module: Electronic-Controlled Power Steering

===END EPS DTC U261B-20===

===IC DTC U1900-20===
Code: U1900 - CAN communication bus fault

Status: 
 - Previously Set DTC - Not Present at Time of Request
 - Malfunction Indicator Lamp is Off for this DTC

Module: Instrument Cluster

Diagnostic Trouble Code details

CAN Communication Bus Fault - Receive Error

Note:

DTCs that start with 'U' are faults which occur during module-to-module communication.

Modules should never be replaced based only on a 'U' code. These codes do not always indicate a problem, and can be caused by normal diagnostic functions, carried out on the vehicle.

===END IC DTC U1900-20===