===PCM DTC P0087-E2===
Code: P0087 - Fuel Rail/System Pressure - Too Low

Additional Fault Symptom:
 - Signal is Below Minimum Threshold

Status: 
 - DTC Present at Time of Request
 - Malfunction Indicator Lamp is On for this DTC

Module: Powertrain Control Module

===END PCM DTC P0087-E2===

===PCM DTC P2127-62===
Code: P2127 - Throttle/Pedal Position Sensor/Switch E Circuit Low Input

Additional Fault Symptom:
 - Signal is Below Minimum Threshold

Status: 
 - DTC Present at Time of Request
 - Malfunction Indicator Lamp is Off for this DTC

Module: Powertrain Control Module

Diagnostic Trouble Code details

Throttle/Pedal Position Sensor/Switch E Circuit Low Input

APPS 2 input voltage is less than the calibrated limit.

Note: This DTC relates to the APPS.

This DTC may be caused by :

Open circuit in wiring or component

Signal shorted to ground or signal return.

Faulty APP Sensor

===END PCM DTC P2127-62===

===PCM DTC P2125-24===
Code: P2125 - Throttle/Pedal Position Sensor/Switch E Circuit

Additional Fault Symptom:
 - There is no change in the signal

Status: 
 - Previously Set DTC - Not Present at Time of Request
 - Malfunction Indicator Lamp is Off for this DTC

Module: Powertrain Control Module

Diagnostic Trouble Code details

Accelerator Pedal Position Sensor/Switch E Circuit

This DTC may be caused by :

Open or grounded circuit.

Signal circuit shorted to VBATT.

Faulty APP Sensor

===END PCM DTC P2125-24===

===PCM DTC P0503-A4===
Code: P0503 - VS Sensor A Intermittent/Erratic/High

Additional Fault Symptom:
 - There is no change in the signal

Status: 
 - Previously Set DTC - Not Present at Time of Request
 - Malfunction Indicator Lamp is On for this DTC

Module: Powertrain Control Module

===END PCM DTC P0503-A4===

===PCM DTC P1260-21===
Code: P1260 - THEFT Detected, Vehicle Immobilized.

Additional Fault Symptom:
 - Signal is Above Maximum Threshold

Status: 
 - Previously Set DTC - Not Present at Time of Request
 - Malfunction Indicator Lamp is Off for this DTC

Module: Powertrain Control Module

===END PCM DTC P1260-21===

===MC DTC U1900-20===
Code: U1900 - CAN communication bus fault

Status: 
 - Previously Set DTC - Not Present at Time of Request
 - Malfunction Indicator Lamp is Off for this DTC

Module: Message Center

Diagnostic Trouble Code details

CAN Communication Bus Fault - Receive Error

Note:

DTCs that start with 'U' are faults which occur during module-to-module communication.

Modules should never be replaced based only on a 'U' code. These codes do not always indicate a problem, and can be caused by normal diagnostic functions, carried out on the vehicle.

===END MC DTC U1900-20===

===ABS DTC U0100-A0===
Code: U0100 - Lost communication with the PCM

Status: 
 - Previously Set DTC - Not Present at Time of Request
 - Malfunction Indicator Lamp is On for this DTC

Module: Antilock braking system

Diagnostic Trouble Code details

Lost communication with the PCM

Note:

DTCs that start with 'U' are faults which occur during module-to-module communication.

Modules should never be replaced based only on a 'U' code. These codes do not always indicate a problem, and can be caused by normal diagnostic functions, carried out on the vehicle.

===END ABS DTC U0100-A0===

===HCM DTC B2622-30===
Code: B2622 - Auto Leveling ECU Speed Message Invalid / Not Available

Status: 
 - Previously Set DTC - Not Present at Time of Request
 - Malfunction Indicator Lamp is Off for this DTC
 - Test not complete

Module: Headlamp Control Module

Diagnostic Trouble Code details

Auto Leveling ECU Speed Message Invalid / Not Available

CAN Communication Bus Fault (missing messages)

===END HCM DTC B2622-30===

===EPS DTC U0100-20===
Code: U0100 - Lost communication with the PCM

Status: 
 - Previously Set DTC - Not Present at Time of Request
 - Malfunction Indicator Lamp is Off for this DTC

Module: Electronic-Controlled Power Steering

Diagnostic Trouble Code details

Lost communication with the PCM

Note:

DTCs that start with 'U' are faults which occur during module-to-module communication.

Modules should never be replaced based only on a 'U' code. These codes do not always indicate a problem, and can be caused by normal diagnostic functions, carried out on the vehicle.

===END EPS DTC U0100-20===

===IC DTC U1900-20===
Code: U1900 - CAN communication bus fault

Status: 
 - Previously Set DTC - Not Present at Time of Request
 - Malfunction Indicator Lamp is Off for this DTC

Module: Instrument Cluster

Diagnostic Trouble Code details

CAN Communication Bus Fault - Receive Error

Note:

DTCs that start with 'U' are faults which occur during module-to-module communication.

Modules should never be replaced based only on a 'U' code. These codes do not always indicate a problem, and can be caused by normal diagnostic functions, carried out on the vehicle.

===END IC DTC U1900-20===



P2125 – Pedal sensor 2 electrical error

P2127 – Pedal sensor 2 electrical error short to ground or open circuit